I'm extremely grateful for all the attention my post has received, but I
don't seem to have explained myself clearly. Imagine two rows. The top row
has only one cell and is a tiny bit wider than the other row. My problem is
getting the two rows to be exactly the same width.
I have tried splitting the rows into two tables and using Table Properties
to set them to the same "preferred width"; I can state my preference, but
Word seems to have a different control that overrides my preference. I wish I
could display that control and edit it, but I can't.
I can also keep rows together in one table and then use
Table|Autofit|Distribute Columns Evenly. But this still does not allow me to
make my own decision about the width of the table.
Stefan Blom was kind enough to give me the link to the MVP note about the
shortcomings of Table Properties
(
http://word.mvps.org/faqs/tblsfldsfms/TablePropPrbs.htm). This lets me
control the cell width, but there seems to be no command to control the table
width or row width.
You're probably wondering how I can get into this fix in the first place.
Well, I do a lot of copying rows from one document to another, then combining
them into tables. That's how I wind up with a table with one row too wide or
too narrow. I'm accustomed to isolating my row and having Table Properties
tell me that a row is 99.7% or 101.4% wide. And if I try to adjust it to
100%, it just doesn't seem to work.
I can get close enough so that nobody else will notice, but it's frustrating
and wastes a lot of time.
Again, I'm very grateful for the attention and helpful suggestions, most of
which I find I have tried.
Maybe my documents are so corrupted that Word can no longer handle them,
though it cheerfully opens and saves them day after day. (I got so frustrated
with my footnote numbering problem that I paid Microsoft the $35 to look into
it for me, though I doubt they'll give me a usable answer. But that belongs
on a different discussion board.)
"Suzanne S. Barnhill" wrote:
I think the issue is that Joe wants a table in which either of two columns
consumes exactly half of a set width. In another row with three columns,
each column would be allocated exactly one third of the same total width.
--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
Word MVP FAQ site: http://word.mvps.org
Email cannot be acknowledged; please post all follow-ups to the newsgroup so
all may benefit.
"Tony Jollans" My Forename at My Surname dot com wrote in message
...
Sorry, Joe, but you've lost me. You cannot manage table width
independently
of cell width - if you change the table width the width of at least one
cell
must also change.
Is there some problem with either or both of the methods I have given you
for precisely setting cell widths?
--
Enjoy,
Tony
"Joe Lewis" wrote in message
...
I can join the tables, then use Table|Autofit|Distribute Columns Evenly
to
ensure that both tables are the same width. But this leaves me with all
columns of the same width, and that's not what I want. I want to manage
the
table width independently of the cell width, as if I were using HTML. It
seems like a reasonable request: I just want to be able to align two
rows
so
they're the same width, without affecting the columns.
"Tony Jollans" wrote:
The exact behaviour of Preferred Widths is a bit difficult to get used
to in
non-standard situations. However, to precisely set cell widths you can
..
(a) use the old Column Width dialog.
To get this go to Tools Customize Commands (tab)
Select "All Commands" under Categories
Scroll down to find TableColumnWidth
Click and Drag it to your favourite toolbar
(b) Press and hold Alt while dragging the cell edge.
--
Enjoy,
Tony
"Joe Lewis" wrote in message
...
Imagine a table with two rows of three cells each. The cells in row
1
need
to
be different widths than those in row 2. If the rows are not quite
the
same
width, there's no way to make them the same width. You can split the
rows
into two tables, use Table Properties to set them to the same
"preferred"
width, but this does not always set them to an exact width.
Frustrating!
----------------
This post is a suggestion for Microsoft, and Microsoft responds to
the
suggestions with the most votes. To vote for this suggestion, click
the "I
Agree" button in the message pane. If you do not see the button,
follow
this
link to open the suggestion in the Microsoft Web-based Newsreader
and
then
click "I Agree" in the message pane.
http://www.microsoft.com/office/comm...id=7466fab8-31
1e-489a-a5b3-2afd5ef3b49c&dg=microsoft.public.word.tables