Home |
Search |
Today's Posts |
|
#1
Posted to microsoft.public.word.mailmerge.fields
|
|||
|
|||
Mail merge to continuous labels skips labels between pages
I am in the same situation as Doug, i.e. no suitable continuous-feed printer
(the ancient Canon BJ300 I just dragged from my cellar just fizzled out, but I had no suitable consumables either). So it's impossible to experiment with the real thing. However, it is possible to examine what Word is outputting, so... I have an Epson 850FX printer and also use the Avery 4013 under XP Pro. Oddly enough, the FX850 driver in XP does not have a continuous paper setting or fanfold setting(why not?). There are certainly no (obvious) settings to set up the /printer/ a certian way, but you can select the "print tray" as tractor and the paper size as 8.5in by 12 in. on an FX850 as far as I can see. By carefully setting the top and bottom margins and the header and footer all to "0" (zero) and the printer driver to 8 by 12 and Print Direct, the extra space can be reduced to only one line space (1/6 inch) on each page, but this throws the second page out of register by one line, and succeeding pages are then further out of register! I had a look at the ESC/P sequences Word generates when you set up Word 2003 to produce Avery 4013 labels. First of all, the page setup Word creates seems OK - it uses a 12in form length and generates the cells necessary for labels 15/16in high each. I set up the driver to use tracter feed 8.5 x 12in continuous feed paper and sent Word's output to a file. Word generates the following ESP/P commands: Header: - printer reset - carriage return (notice that that should not normally affect vertical position - set PC437 character set - set characters 128-159 to be printable - set USA character set - set NLQ mode - set 10cpi font - set line spacing to 1/6in - set page length to 84 lines - carriage return It then essentially repeats the following for each page: - carriage return - move down a specified amount - move right a specified amount - send a line of 9-pin graphics - form feed At the very end, it outputs - carriage return Now the really weird thing about that is that 84 lines at 1/6in spacing isn't 12in but 14in, so if I were printing that stuff on an LX850, I would expect to see a 2in gap at the bottom of each page. That's not what you're reporting, but it is almost precisely what Devon Stout reported in the original post in this thread. However, at this point a. there are too many variables to explore withut a real printer with which to experiment b. I've begun to doubt my own findings so I wonder if anyone else is in a position to look at this stuff? If you, "CMLCBigGuy", would like to do a similar experiment, all you really need do is set up the FX850 driver to output to the FILE: device instead of (say) LPT1: and generate 2 to 3 pages of labels. If you know how to examine the ESC/P codes yourself, fine, but if you don't, by all means despam my e-mail address and send me the output for 2-3 pages of labels and I'll compare it with the above findings. FWIW the circumstances in which I can imagine Word behaving the way /you/ (CMLCBigGuy) report a a. Word never outputs FF, and miscalculates the page length by one line per page b. Word sets page length to be one more line than it is c. Word does FF, then outputs a line, then sets page length, (which, for Epson printers, resets the top of page). However, the ESC/P sequences I see do not seem to be doing that... Peter Jamieson "CMLCBigGuy" wrote in message ... At this point I am tempted to reply with stronger language, worthy of Eric S. Raymond, but I will stay my hand in the interest of communication and of helping others... This problem is not printer-specific! It happens on any printer. You do not need to have this specific printer to investigate this problem! Note that I and others on this forum have seen this problem while using other printers. This is NOT a problem with the printer. Please investigate! Thank you, "Doug Robbins - Word MVP" wrote: I do not have such a printer so I cannot investigate your problem. -- Hope this helps. Please reply to the newsgroup unless you wish to avail yourself of my services on a paid consulting basis. Doug Robbins - Word MVP "CMLCBigGuy" wrote in message ... I would suggest that this is NOT a printer driver problem. I proved this to my satisfaction by running labels successfully using another program and the SAME printer driver! Epson does not have a printer driver for this printer under XP--they do for Win98 and ME. I note many people on this forum complaining of this, and while some may be due to printer settings, not all are! Please investigate. Thank you, CMLCBigGuy "Doug Robbins - Word MVP" wrote: I would suggest that it is a printer driver problem. See if Epson has an updated driver for the printer. -- Hope this helps. |
Reply |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Mail Merge Word 2003 Issue | Mailmerge | |||
In Mail Merge, print many continuous different labels from Excel? | Mailmerge | |||
mail merge using one-up labels | Mailmerge | |||
many duplicates when i try to mail merge labels | Mailmerge | |||
printing file labels - mail merge | Mailmerge |