One other note: Depending on what LJ you have, you may be able to add 6" x
8.5" as a defined paper size in the printer Properties. The LJ 4100, for
example, permits a certain number of user-defined sizes.
--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
Word MVP FAQ site:
http://word.mvps.org
Email cannot be acknowledged; please post all follow-ups to the newsgroup so
all may benefit.
"Suzanne S. Barnhill" wrote in message
...
When you select the paper size in Page Setup, do you see 6" x 8.5" listed
as
a paper size? No? I thought not. In that case, you're having to set it up
as
a custom size. HP LaserJets differ in how they handle custom sizes. My LJ
4
fed small sizes on the left; the LJ 4100 feeds built-in small sizes from
the
center (where the paper guides converge) but custom small sizes from the
left. This means I have two choices: (1) set up a custom size and feed it
from the left, unable to take advantage of the paper guides, or (b) set up
the custom size in the center of a Letter-sized page and feed it from the
center. I tend to do a little of both.
You'll have to experiment to see how your printer deals with smaller
custom
sizes and make your choice based on that, but I would imagine that option
2
would probably be more satisfactory for duplexing. Basically what you do
is
figure out where the content of your small page would print on a page of
Letter paper. Then adjust the margins accordingly.
For example, say you have 0.75" margins all the way around your 6" x 8.5"
page. Assuming that the printer is going to start printing at the top of
the
page as fed, you'll need to add 2.5" (the difference between 11" and 8.5")
to just the bottom margin, giving you a 3.25" bottom margin and a 0.75"
top
margin. You will also need to adjust the header and footer margins
accordingly.
For the side margins, you'll need to add a total of 2.5" (the difference
between 8.5" and 6"). Whether you add this all on one side or divided
between them will depend on the results of your experiments with where the
page prints relative to where you want to feed it. You'll end up with
margins of ) .75" and 3.25" on the left and right or 2" on both sides. The
body of your document (including footnotes) will be confined within these
margins; the header and footer will be placed at the header and footer
margins you set. It may help you to lay your 6" x 8.5" page on top of a
sheet of Letter paper and draw around it to get the concept of what you're
trying to do.
--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
Word MVP FAQ site: http://word.mvps.org
Email cannot be acknowledged; please post all follow-ups to the newsgroup
so
all may benefit.
"mkraft" wrote in message
news
The question here is whether your printer actually has a definition
for
the
6 x 8.5" paper size.
Thanks. How would I be able to determine that? It's an HP Laserjet, so
I
assume it's as versatile as most printers in handling different paper
sizes.
If not, and if you're setting it up as a Custom size,
In Word, 6 x 8 1/2 would have to be set up as a 'custom' size, wouldn't
it?
Instead, set it up as Letter (or the closest larger size) and increase
the margins
accordingly (including the required gutter or different in Mirror
Margins).
Can you explain this a bit, I don't think I follow you. Do you mean to
use
a standard (i.e., non-custom) paper size and simply adjust the size of
the
table to conform to 6 x 8 1/2? If so, what about footnotes, headers,
footers, etc.?