I think I probably haven't done it in Windows 2000 because I just copied the
file I had from an earlier version. I suspect that if I ran the macro now
(if it worked), I'd get a lot more button faces than my current table
includes, which would probably be worthwhile.
--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
Word MVP FAQ site:
http://word.mvps.org
Email cannot be acknowledged; please post all follow-ups to the newsgroup so
all may benefit.
"StargateFan" wrote in message
...
On Fri, 24 Feb 2006 09:06:42 -0600, "Suzanne S. Barnhill"
wrote:
It's been so long since I did this that perhaps I'm thinking of something
different, but when I did it, the macro created a table that could be
saved
as a document. IOW, it was not necessary to run the macro more than once.
Yes, it did but imperfectly. There was an error in the macro each
time and only a fraction of FACEIDs were done. Sorry, should have
mentioned. There were also a few repeats.
Also, copying the images wouldn't work so was very glad when it worked
yesterday but it's doing it again! I can't understand the problems
I'm having with Windows 2000. It's got to be a windows problem (?) as
the only time this worked was right after I put in service pack 3!
sigh I'm having all sorts of little glitches that are really
annoying. One upgrades to a "higher" OS only to have troubles one
didn't have with an older one!
So going to post in Windows 2000 groups. Hopefully someone there
knows what might be going one!
--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
Word MVP FAQ site: http://word.mvps.org
Email cannot be acknowledged; please post all follow-ups to the newsgroup
so
all may benefit.
"StargateFan" wrote in message
.. .
On Thu, 23 Feb 2006 10:09:11 -0600, "Suzanne S. Barnhill"
wrote:
IIRC, the template contains a macro (which must be enabled) that you
have
to
run to produce the button image table.
Yes, as I mentioned, changed macro security level to medium and when
file pops up, I enable the macros same as always. All I get is a
flicker of the FACEID panes and then everything disappears.
...
Well, go figure! I hadn't installed service pack 3 for Windows 2000
I realized after posting this msg so went and did that yesterday.
Same problem persisted yesterday even after that and even after a
couple of reboots but just now, to be sure, I went to check one last
time to see if this still persisted. I got the FACEID panes and they
stayed! Guess it needed 3 reboots to work! g
Guess it was a Windows problem after all. I'm not holding my breath,
but hopefully this continues to work. I use these FACEID panes quite
a bit. I went hunting for other files in both Word and Excel but none
are as good as this one as it presents all the icons in only 4 panes!
Thanks. Sorry to have bothered the group, but so far, so good
fingers crossed. 
D
--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
Word MVP FAQ site: http://word.mvps.org
Email cannot be acknowledged; please post all follow-ups to the
newsgroup
so
all may benefit.
"StargateFan" wrote in message
.. .
Don't know if this is a Windows 2000 or a Word question, so pls
advise
if I'm in the wrong ng.
A few years back I dl the FACEID document from this webpage,
http://word.mvps.org/FAQs/Customizat...ttonImages.htm, or
one
similar. Since I dl, it worked fine all the time in Win98SE. In my
new installation of Windows 2000, it doesn't work properly. I get a
blank document labelled template1 but nothing shows up. If I change
docts via the Window pulldown, it flickers on for a moment but then
again disappears. At first I had thought it might be the macro
security and so changed that to medium, but problem persists.
Does anyone know where I can look for a solution to this problem?
Again, if there is a better ng, pls advise.
Thanks. D