How EXACTLY does one do this? There doesn't seem to be an "Insert Frame"
option on the menu and the Frames toolbar isn't intuitive either. There's an
option in Format Textbox that allows you to convert a textbox to a frame, but
I'm guessing you need to have the textbox populated with the information
first (but that's not what you described). Based on your description below,
it sounds like there's another way.

I could really use the help. We just switched to Word 2003 and I've spent a
whole day (and $40 on a book!) just trying to do the same things I did in
about 10 minutes using Word 2000. I don't think the upgrade was worth it.

Thanks!
Donna

"Suzanne S. Barnhill" wrote:

If you will insert your graphics in line with text instead of wrapped, then
the caption will also be inline instead of in a text box. You can then
select both graphic and caption and insert a frame to contain them both,
wrapping text around the entire frame. Word will not see captions in text
boxes, anyway, so if you plan to generate a List of Figures, you need to get
the caption out of the text box.

--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
Word MVP FAQ site: http://word.mvps.org
Email cannot be acknowledged; please post all follow-ups to the newsgroup so
all may benefit.

"EugenioB" wrote in message
...
All I can guess is that:
I have not explained the problem sufficiently, or
everyone has missed something in reading my original post, or
the AutoCaption feature works differently for me than it does for others.

I'll try to address the first possibility.

I presume that this feature was designed to save time/effort in creating a
separate caption for each insertion and to ensure consistency of
format/position/etc of all the figure/table/equation captions in a
document.
It certainly is not saving me any time.

When I activate it for the insertion of graphics files, specifying the
built-in settings "figures" and "below", what it seems to do when I
Insert-Picture-FromFile is to place an extra line of left-justified text
in
"Caption" style (with no frame or other formatting) a couple of vertical
line
spaces below the graphic. This line contains the text: "Figure n"
(n=sequential number of the insertion). This text does not appear to have
any
"special" characteristics that I can see/rollover/click on (even if I
reveal
the formatting codes), but does have some "magical" properties, since I
can
insert cross-references to it elsewhere in the document.

After re-sizing the graphic and setting the text flow and layout
properties
(at the moment Top&Bottom flow with 0.4cm gaps and centred in a column), I
centre the Caption text line and all seems fine. If I then shift the
graphic
up or down a couple of lines within the document, one or two lines of text
flow into the gap between the graphic frame and the caption. Yes: between
the
graphic and its caption. There is no frame around the caption to adjust.
There is nothing but the graphic for the "Select Objects" tool to select
for
grouping.

By "playing around" with positioning, I have so far managed to avoid this
problem, making the text flowing into the gap end up just as a single
blank
line, but I have now ended up in a situation I cannot change, where the
caption has flowed onto the page following the one where the graphic is
located. Again: the graphic and its caption end up on different pages.
Moving
the graphic higher brings the caption back onto the same page, but apart
from
this position not being acceptable for this particular document's logic,
one
or two lines of text always seem to remain between the graphic and its
caption. If I force the graphic to go onto the next page, it ends up
aligned
with the top edge of the "virtual paper" and its caption drops to a couple
of
lines below the first text. Any further manipulation causes the graphic to
end up somewhere else in the document, sometimes a couple of pages away,
sometimes behind another graphic (even though the properties of both
graphics
initially have the "Allow overlap" unchecked), and I end up having to Undo
to
find it.

What a mess, MS!

I wish I could attach an example to illustrate the above explanation.

EB


"EugenioB" wrote:

I am having trouble with AutoCaptions for Figures (inserted pictures)
separating from the images. The document's text slips into the gap
between
the caption and pictures when fine-adjusting picture position. Sometimes
this
results in the Caption ending up on the page following the picture.
The text flow is set for Top&Bottom wrapping, with 0.4cm gap each. The
AutoCaption Position is set to Below Item.
Manually-inserted Captions do not do this, because the Caption is
inserted
into a frame, with no gap to the picture.