[Richard[_2_]]

Sometimes the end of a chapter (say) ends on the obverse, which is probably
(but not exclusively) an odd page number. The next chapter starts on the
next even number, and, if you are printing duplex, the first page of the new
chapter is printed on the back of the page - that is, it gets printed on the
reverse of the page.

Now of course you can have a blank page after the end of the chapter, and
that will ensure that the next chaper is printed on the obverse, that is the
next chapter starts on the obverse, rather than the reverse. But, you would
not want the page numbering to change.

I'm doing duplex printing: Is there a way to get the page that would
normally print on the reverse, to print on the obverse, and a way not avoid
alteration in the page numbering? So start of (say) chapter 2 had the same
page number as originally.

TIA.

[Richard[_2_]]

"Richard" wrote in message
...
Sometimes the end of a chapter (say) ends on the obverse, which is
probably (but not exclusively) an odd page number. The next chapter starts
on the next even number, and, if you are printing duplex, the first page
of the new chapter is printed on the back of the page - that is, it gets
printed on the reverse of the page.

Now of course you can have a blank page after the end of the chapter, and
that will ensure that the next chaper is printed on the obverse, that is
the next chapter starts on the obverse, rather than the reverse. But, you
would not want the page numbering to change.

I'm doing duplex printing: Is there a way to get the page that would
normally print on the reverse, to print on the obverse, and a way not
avoid alteration in the page numbering? So start of (say) chapter 2 had
the same page number as originally.

TIA.

I have page 41 which is end of a hapter. Then there is "section break (Next
Page), then after that starts page 42. Page 42 is printing on the back of
page 41, because I'm running duplex printing.

Something here has to change, we don't want page 42 to print on the back of
page 41, but on a the next clean sheet. I don't know what break to put in.

[Suzanne S. Barnhill]

You can't get page 42 to print on an odd page. What you can do is change
your Next Page section break to Odd Page. This will cause Word to insert a
totally blank page 42 after 41, and your next chapter will start on page 43.

--
Suzanne S. Barnhill
Microsoft MVP (Word)
Words into Type
Fairhope, Alabama USA
http://word.mvps.org

"Richard" wrote in message
...

"Richard" wrote in message
...
Sometimes the end of a chapter (say) ends on the obverse, which is
probably (but not exclusively) an odd page number. The next chapter
starts
on the next even number, and, if you are printing duplex, the first page
of the new chapter is printed on the back of the page - that is, it gets
printed on the reverse of the page.

Now of course you can have a blank page after the end of the chapter, and
that will ensure that the next chaper is printed on the obverse, that is
the next chapter starts on the obverse, rather than the reverse. But, you
would not want the page numbering to change.

I'm doing duplex printing: Is there a way to get the page that would
normally print on the reverse, to print on the obverse, and a way not
avoid alteration in the page numbering? So start of (say) chapter 2 had
the same page number as originally.

TIA.

I have page 41 which is end of a hapter. Then there is "section break
(Next
Page), then after that starts page 42. Page 42 is printing on the back of
page 41, because I'm running duplex printing.

Something here has to change, we don't want page 42 to print on the back
of
page 41, but on a the next clean sheet. I don't know what break to put in.